tProbe™ – T1 E1 VF and Serial Data Analysis and Emulation Hardware

מאפיינים מרכזיים

This hardware incorporates all the features of the previous analyzer such as portability, USB interface, remote accessibility, scripting, and a vast collection of optional applications.

Recently tProbe™ was introduced with the following important enhancements:

  • T1 E1 Pulse ShapeJitter Measurement Analysis and Jitter Generation
  • tProbe™ FXO and FXS board allows simulating FXO and FXS ports; FXO port to simulate a two-wire FXO device such as a telephone or a fax machine and the FXS port on tProbe™ to emulate a 2-wire FXS service such as a telephone wall jack.
  • tProbe™ Datacom Analyzer board supports V.24, V.35, V.36, RS-449, RS-485, EIA-530 and EIA-530A interfaces and can be configured as DTE or DCE to test Channel Service Unit (CSU) and Data Service Unit (DSU) entities
  • Software selectable T1 or E1 interface along with Drop and Insert
  • Monitor the T1/E1 line conditions such as frame errors, violations, alarms, frequency, power level, and clock (or frame/bit) slips.
  • TDM, ISDN, SS7 – High Density Voice
  • VoIP, Frame Relay, Multilink Frame Relay, PPP and Multilink PPP, HDLC
  • Physical layer analysis includes ability to send alarms and errors via SNMP Traps
  • Routing and Bridging emulation over Multi T1/E1 WAN interfaces using MLPPP (Multi Link PPP) and MFR (Multi Link Frame relay) protocols
  • Call Recording, Generation, and Monitoring for hundreds to thousands of calls in one platform
  • Capable of simulating as well as decoding and demodulating fax calls over T1/E1 lines using Fax Simulator andFaxScan™
  • Windows® and Linux Drivers for Open Source Applications
  • Supports both 32-bit and 64-bit Windows® operating system.
  • "Cross-port Through" and "Cross-port Transmit" Modes – these configurations make cabling with Drop/Insert and Fail-Safe Inline Monitoring very easy
  • Support for all  "basic applications" and "special applications"
  • Comprehensive Analysis / Emulation of Voice, Data, Fax, Protocol, Analog, and Digital signals, including Echo and Voice Quality testing
  • Improved circuitry for very accurate Digital Line Level measurements
  • Ethernet Interface for future standalone operation
  • Easy calibration
  • Forward thinking hardware design for future daughter board expansion applications
  • Lightweight (1.24 lbs) and small footprint (6.05" x 5.55" x 1.60 ")
  • Switchable Line Level or Microphone input using 3.5 mm or Bantam physical connectors
  • Enhanced VF Drop and VF Insert Capabilities using 3.5mm Balanced (Stereo), or Unbalanced (Mono) physical connections.
  • Includes individual speakers (one speaker per card).
  • The VF Tx and Rx impedance for tProbe™ analyzer supports software selectable 135, 150, 600, or 900 Ohm terminations. Additionally, the VF Rx impedance supports New High Impedance Monitor Termination (>50K Ohms), and external Microphone and Headset (Mic/HS) impedance .
  • VF Tx Gains for tProbe™ analyzer ranges from -12 dB to +59.5 dB in 0.5 dB steps, and VF Rx Gains for tProbe™analyzer ranges from -63.5 dB to +9 dB in 0.5 dB steps.
Physical Interface
USB Connector (1) USB TYPE B Jack
Ethernet Connector (1) RJ-45 10/100 Ethernet Jack
T1/E1 Connectors (2) RJ-48c Jacks
Audio Connectors (4) 3.5 mm Balanced (Stereo) or unbalanced (Mono) Audio Jacks (TX & RX)
External Clock Connector (1) MCX Coaxial Jack
External Power Connector (1) Coaxial DC Power Jack (mates with 5.5mm x 2.1mm coaxial plug)
Physical Dimensions
Dimensions 6.05 inches (153.67mm) (L)
5.55 inches (141.224mm) (W)
1.60 inches (40.64mm)  (H)
Weight 1.24 lbs. (0.56 kg)
Operating Temperature Temperature
0° C to 50° C
10%-95% Humidity, Non-condensingStorage
-20° C to 70° C
10%-95% Humidity, Non-condensing.
Altitude 10,000 Feet
Acoustic Noise NA
External Power Requirements
Power Adapter Requirements +5V @ 2A Max Power to the Center Ring
Optional Boards
2-Wire Daughter Board (One FXO, One FXS) FXO – RJ-11
2W Call/Answer
Caller ID
T1 to 2W FXO Drop
2W FXO Insert to T1
PC to 2W FXO Drop
2W FXO Insert to PC
FXS – RJ-11
2W FXS
Ring Voltage
Battery Voltage Generation
T1 to 2W FXS Drop
2W FXS Insert to T1
PC to 2W FXS Drop
2W FXS Insert to PC
Datacom Daughter Board Dual DB25 Connectors Support:
DTE/DCE
RS-232/V.28
X.21/V.11
RS-449/V.36 /V.10/V.11
EIA-530/V.10/V.11
EIA-530A/V.10/V.11
V.35/V.28.
>T1/E1 Line Interface
Framing Formats Unframed, D4 (T1) , ESF(T1), CAS(E1), FAS(E1), CRC4
Hardware Compliant: SLC96, T1ESF ZBTSI
Line Code format AMI, B8ZS (T1) or HDB3 (E1)
Internal Clock Specification Standard: ± 3ppm  Optional: ± 1ppm
Output Clock Source Internal (± 1 ppm or 3 ppm), Recovered, External Clock
T1 Output Level T1: 3.0V Base to Peak Selectable 0-655Ft Pulse Equalization Setting; Tx Capability – DSX-1 Outputs (to 655 feet)
E1 Output Level E1: 3.0V ±  0.3V Base to Peak
Input Level 75 mV to 6V base to peak or -30 dBsx to -6 dBsx
Line Built Out Selections 0dB, -7.5dB, -15dB, -22.5dB for T1 only
Loopback Normal (Outward and Inward)
Cross-Port Transmit Loopback
Cross-Port Through Loopback
>Transmit
T1/E1 Interface Hardware Compliance – ANSI: T1.403.1995, T1.231-1993, T1.408
– AT&T: TR54016, TR62411
– ITU: G.703, G.704, G.706, G.736, G.775,  G.823, G.932, I.431, O.151, Q.161
– ITU-T: Recommendation I.432-03/93 B-ISDN User-Network Interface-Physical Layer Spec
– ETSI: ETS 300 011, ETS 300 166, ETS 300 233, CTR12, CRT4
– Japanese: JTG.703, JTI.431, JJ-20.11 (CMI Coding Only)
BERT Pattern Generation Pseudorandom patterns: (63) 26-1, (511) 29-1, (2047) 211-1, (32767) 215-1, (1048575) 220-1, (8388607) 223-1, QRSS.
Hardware Compliant: T1 In-Band Loop Code Generation and Detection
Fixed patterns: All Ones, All Zeros, 1:1, 1:7, 3 in 24, User Defined 24- Bits
Hardware Compliant: User pattern of up to 32 bits in length
Alarm Insertion Blue, Yellow, Remote, Distant Multiframe
Hardware Compliant:
Bit 7 Zero Suppression
D4 Yellow: 1 in S bit of frame 12
AIS-CI Code, ESF-RAI CI Code
Receive Carrier Loss: 0’s for 2047 or 255 bits (For E1 only)
Error Insertion BPV, Bit Error, Frame Error, CRC Errors, Burst Frames, Fixed Error Rate, Random Error Rate, auto logic from 10-2 to 10-9 for selectable 56K or 64Kps channels.
Drop and Insert Any contiguous set of digital timeslots and/or audio input
Facility Data Link T1 ESF Mode: Transmit/Receive Messages, Bit-Oriented Messages, and Files.
Zero Suppression B7 Stuffing, Transparent, & B8ZS (T1)
Signaling Robbed-Bit or Clear Channel
Frequency Offset T1: +/- 615Hz

E1: +/- 615Hz

>Receive
Input Impedance 100 ohms for Terminate and Monitor (T1)
120 ohms for Terminate and Monitor (E1)
> 1K ohms for Bridge
Terminations Terminate, Monitor, Bridge
T1 Input Frequency 1.544MHz ± 20KHz
E1 Input Frequency 2.048Mhz ± 20KHz
Frequency Measurement ± 1ppm
Error Detection Frame Error, CRC Error, BPV Error, Logic Error, Frame Alignment Error
Hardware Compliant:
* 10 or 24 bits for sync time
* 2/4, 2/5, or 2/6 frame bit in error frame select
* Frame error bit corruption for 1 or 3 frame bits
* E-Bit Error
* Line Code Violation
Alarm Detection T1 – D4 Yellow Alarm, ESF Yellow Alarm
Yellow Alarm (B2 Suppressed-2nd MSB)
Yellow Alarm (S-Bit)
Yellow Alarm (00FF in FDL)
Blue Alarm (Framed or Unframed All Ones)
E1 – Remote Alarm
Distant MultiFrame Alarm
Signaling All Ones
Unframed All Ones
Hardware Compliant: J1 Yellow Alarm
Intrinsic Jitter Meets Jitter Tolerance:
Meets AT&T TR 62411 (Dec. 90)
Meets ITU-T G.823
Jitter Transfer:
Meets AT&T TR 62411 (Dec. 90)
Input Range T1: Terminate, 0 to 36dB (Long Haul), DSX Monitor, Bridge
Hardware Compliant: Terminate, 0 to 15dB (Limited Long Haul), DSX Monitor 20dB, 26dB, 32dB
E1: Terminate, 0 to 43dB (Long Haul), DSX  Monitor, Bridge
Hardware Compliant: Terminate, 0 to 13dB (Short Haul), DSX Monitor 20dB, 26dB, 32dB
>Display and Logging
BERT Bit Errors, Bit Error Rate, Error Seconds, Error Free Seconds, %EFS, Severely Error Seconds, % SES, Degraded Minutes, %Dmin, Loss Pattern Sync Count, Loss of Sync Seconds, Available Seconds, %Available Seconds, Unavailable Seconds, Bipolar Violations, BPV Rate, BPV Seconds, BPV Free Seconds, Frame Errors, FE Rate, FE Seconds, FE Free Seconds, with Detailed logging into disk file.
Alarms Resync In Progress, Loss of Signal, Blue Alarm, Change of Frame Alignment, Bipolar Violation, Frame Error, Carrier Loss, Yellow Alarm, Out of Frame Events Counter, Error Super frame Counter, Bipolar Violations, Remote Alarm, Distant Multiframe Alarm, Signaling All Ones, CAS Multiframe Error, CRC4 Error.
VF Drop and Insert
Refer to VF Drop and Insert Capabilities webpage for more details.
Rx Termination High Impedance (>50K Ohms) for Non-Intrusive Testing
Software selectable 135, 150, 600, 900 Ohms for Intrusive Testing
Provision for external Microphone (Mic/HS) on VF ports connection
External Microphone and Headset (Mic/HS) on VF ports connection
Tx Termination 135, 150, 600, 900 Ohms
Sampling Rates 8KHz
Datawidth (bits)  Supports 8, 16, 20, 24, 32 Bit Data
VF Tx Gains Supports -12 dB to +59 dB in 0.5dB Steps Gain (0.1 dB steps can also be accommodated in tProbe™)
VF Rx Gains Supports -63.5 dB to +9 dB in 0.5dB Steps Attenuation (0.1 dB steps can also be accommodated in tProbe™)
Connectors (4) 3.5 mm Balanced (Stereo) or Unbalanced (Mono) Audio Jacks (TX & RX)
לקבלת מידע צור קשר השאירו פרטיכם ונחזור אליכם